Show simple item record

dc.contributor.authorMakrides, Georgeen
dc.contributor.authorZinsser, Bastianen
dc.contributor.authorPhinikarides, Alexanderen
dc.contributor.authorSchubert, Markusen
dc.contributor.authorGeorghiou, George E.en
dc.creatorMakrides, Georgeen
dc.creatorZinsser, Bastianen
dc.creatorPhinikarides, Alexanderen
dc.creatorSchubert, Markusen
dc.creatorGeorghiou, George E.en
dc.date.accessioned2019-04-08T07:47:06Z
dc.date.available2019-04-08T07:47:06Z
dc.date.issued2012
dc.identifier.urihttp://gnosis.library.ucy.ac.cy/handle/7/44157
dc.description.abstractAbstract The effect of temperature on different grid-connected photovoltaic (PV) technologies installed in Cyprus was analyzed in this study. Initially, the performance losses due to the temperature effect on the annual energy yield of each technology were investigated using measurements of module temperature and the manufacturer provided maximum power point (MPP) temperature coefficients, γPMPP. The same methodology was also applied using outdoor evaluated γPMPP coefficients for comparison. When using the manufacturer’s temperature coefficient, the results showed that over the evaluation period the highest average thermal losses in annual dc energy yield were 8% for mono-crystalline silicon (mono-c-Si) and 9% for multi-crystalline silicon (multi-c-Si) technologies while for thin-film technologies, the average losses were 5%. Similar losses were found when using the outdoor evaluated temperature coefficients. Additionally, temperature effects on the seasonal performance of the different technologies were evident on the monthly average performance ratio (PR). For the amorphous silicon (a-Si) technologies, a performance increase from spring until early autumn was observed and was attributed to thermal annealing. The effect of thermal annealing on the performance was evident by filtering dc MPP power measurements at high irradiance (greater than 800 W/m2) and restricting the values at geometric air mass (AM) in the range 1 ≤ geometric AM ≤ 1.5. The extracted dc MPP power was corrected for irradiance and temperature at standard test conditions (STC) using the manufacturer provided γPMPP over a period of two years. Subsequently, the effect of thermal annealing was further investigated by extracting dc MPP power measurements at geometric AM in the range 1.4 ≤ geometric AM ≤ 1.6 in order to minimize the spectral influences on the performance of a-Si technologies. An increase in power for all the a-Si technologies was obvious during the warm summer season and was recorded over the period of March until September for both years. "en
dc.sourceRenewable Energyen
dc.source.urihttp://www.sciencedirect.com/science/article/pii/S0960148111006483
dc.subjectTemperatureen
dc.subjectAmorphous siliconen
dc.subjectPhotovoltaic systemen
dc.subjectThermal annealingen
dc.subjectThermal lossesen
dc.titleTemperature and thermal annealing effects on different photovoltaic technologiesen
dc.typeinfo:eu-repo/semantics/article
dc.identifier.doi10.1016/j.renene.2011.11.046
dc.description.volume43
dc.description.issueSupplement Cen
dc.description.startingpage407
dc.description.endingpage417
dc.author.facultyΠολυτεχνική Σχολή / Faculty of Engineering
dc.author.departmentΤμήμα Ηλεκτρολόγων Μηχανικών και Μηχανικών Υπολογιστών / Department of Electrical and Computer Engineering
dc.type.uhtypeArticleen
dc.contributor.orcidGeorghiou, George E. [0000-0002-5872-5851]
dc.gnosis.orcid0000-0002-5872-5851


Files in this item

FilesSizeFormatView

There are no files associated with this item.

This item appears in the following Collection(s)

Show simple item record